In a previous article we wrote about the no waste hay feeders we use with our flock. These feeders were designed to hold small amounts of hay like square bales or hay that we peeled off of round bales. But what if you have enough sheep and equipment to warrant the labor savings of feeding whole round bales? Today we are going to show you what we have found to work well as a round bale feeder for sheep.
In our opinion, the ease and labor savings of feeding whole round bales is worth it under 2 conditions. If feeding it outside, you’ll need to be able to use a round bale in less than a week to avoid it being spoiled by rain. You also need to be able to feed them without wasting the majority of the bale.
Unfortunately, preventing waste is not as easy with small ruminants as it is with cows and horses.
Left to their own devices sheep can waste 50% or more of a bale if not fed in a feeder. This is economically unacceptable in our opinion. However, most round bale feeders are designed for cows and horses not sheep and goats. Thus, they do not work very well, or at all for small ruminants. Either the sheep can’t reach the hay, or they can get inside the feeder defeating the purpose. Some feeders like many cradle feeders can be dangerous to use.
There are a few round bale feeders designed with sheep in mind. In many cases they are prohibitively expensive or difficult to obtain. Probably one of the most common DIY designs is using a cattle panel with larger holes cut in it wrapped around a bale. This is certainly better than nothing, but we thought there had to be a better solution.
The result is our corral panel feeder.
The idea of this feeder is to incorporate the collapsible nature of the expensive sheep feeders we’ve seen with what we’ve learned over the years about slowing down hay waste. This feeder is simple to make, easy to move, and works well for our flock.
We typically feed 4×5 bales, so this feeder is suitable for similarly or smaller sized bales. You may need larger corral panels, or a 4th one if you feed different size/shape bales. We like this feeder because it works well. It’s inexpensive, durable, and portable. It also doesn’t require having a tractor capable of lifting bales over the ring.
To make this feeder, you will need a few simple tools, mainly a drill and a way to cut chain. Then you will need three 12’ corral panels, three boards 1x6x12 (or 2x6x12), lengths of chain (like that used on pipe gates), bolts to attach the boards to the corral panels, and snap clips. You will also need an optional round bale hay net.
To make the feeder:
Start by drilling holes and attaching the board to the bottom of the corral panel as seen in the picture below. This is to help keep the hay inside the feeder, and their feet from going under or through the bottom to step on the hay inside. Without it your bale net and hay that has collapsed down near the bottom are likely to get trampled into the mud.
You will need to cut your chain into 6 pieces that are long enough to wrap around 2 corral panel tubes and be clipped together to support your panels. These are to allow you to shrink the feeder as the bale gets smaller.
Once you have done these two things you’re ready to set up the feeder.
Put a bale net on your round bale and place it out into the field. We typically put the bale net on after the bale is almost in place, right before we set it down. That way we can cut and remove the twine without worrying about the bale collapsing as we are transporting it. Our preference is to place the bale up on a pallet rather than setting it directly on the ground.
Once your bale is in place you can set up the feeder around it. Arrange your corral panels in a triangle around the bale. Initially, you can probably just use the corral panel pins to hold them together. The bale is likely large enough for the sheep to reach. A tarp can also be easily thrown over the top of this feeder and tied off to help protect your hay from rain or snow.
Once your flock has eaten most of what they can reach, you can start shrinking your feeder. To do this you will pull one end of each panel out past the next panel like a pinwheel. Use the pieces of chain to secure the panels to each other to prevent them from falling. You can also do the same thing with 4 panels instead of 3 if you’d prefer. When the bale is gone, simply un-clip the panels, drag them to your next location and start again.
We find that these feeders provide an acceptably low level of waste.
The level of waste from these feeders is probably on par with the waste from our other feeders, but with massive day to day labor savings. Our waste is well less than 10% if we are feeding decent quality hay and use a bale net. While we said a bale net is optional, it does really help cut down on waste. It prevents the sheep from dragging large chunks of hay off the bale and out of the feeder.
Keep in mind also that the quality of your hay will directly affect the amount of waste you get. Good quality hay will produce the least waste. If your hay is full of weeds and straw, it doesn’t matter what feeder you use, they will pick through and leave the inedible parts.
We hope that this idea will help you to save time and money on your farm.
If you would like to learn more about how we do things on our farm, don’t forget to subscribe to our newsletter!
Please remember
The information provided is for general informational purposes only. All information on the site is provided in good faith, for general informational and educational purposes only and is not a substitute for professional advice. We make no representation or warranty of any kind, express or implied, regarding the accuracy, adequacy, validity, reliability, availability, or completeness of any information on this Site. Accordingly, before taking any actions based upon such information, we encourage you to consult with the appropriate professionals. We do not provide any kind of professional advice. THE USE OR RELIANCE OF ANY INFORMATION CONTAINED ON THE SITE IS SOLELY AT YOUR OWN RISK. View full disclaimer here.
